200-601試験対策書,200-601試験概要,200-601受験記対策,200-601難易度,200-601ITパスポート

どんなツールが最高なのかを知りたいですか。いま教えてあげます。Ktestの200-601試験問題集が最高のツールです。Managing Industrial Networking for Manufacturing with Cisco Technologies問題集には試験の優秀な過去問が集められ、しかも最新のシラバスに従って出題される可能性がある新しい問題も追加しました。これはあなたが一回で試験に合格することを保証できる問題集です。Ktestは異なるトレーニングツールと資源を提供してあなたのCCNA Industrial資格の200-601試験問題集の認証試験の準備にヘルプを差し上げます。編成チュートリアルは授業コース、実践検定、試験エンジンと一部の無料なPDFダウンロードを含めています。
Share some CCNA Industrial 200-601 exam questions and answers below.
Which configuration enables an Industrial Ethernet switch to participate in PTP clock selection and sets the priority value that would break the tie between switches with matching default criteria to 50?

A. ptp mode boundary

ptp priority1 10

ptp priority2 50

B. ptp mode boundary

ptp priority1 50

ptp priority2 10

C. ptp mode e2etransparent

ptp priority1 50

ptp priority2 10

D. ptp mode e2etransparent

ptp priority1 10

ptp priority2 50

Answer: A

Which configuration enables an Industrial Ethernet switch to participate in PTP clock selection and sets the priority value that would break the tie between switches with matching default criteria to 50?

A. ptp mode boundary ptp priority1 10 ptp priority2 50

B. ptp mode boundary ptp priority1 50 ptp priority2 10

C. ptp mode e2etransparent ptp priority1 50 ptp priority2 10

D. ptp mode e2etransparent ptp priority1 10 ptp priority2 50

Answer: A

Which selection is a reason why IGMP snooping should be configured on a switched network?

A. IGMP snooping populates the snooping table with the results of DHCP requests and can be used by Dynamic ARP Inspection to block IP spoofing attacks at Layer-2.

B. IGMP snooping verifies the source IP address of every IPv4 packet to ensure that it hasn’t been originated from a port different than its return path.

C. IGMP snooping is used to filter ping requests and results to avoid overflowing the MAC address table of the switch.

D. IGMP snooping allows a Layer-2 switch to limit the transmission of multicast frames to only the ports that have members of the relevant IGMP group.

Answer: D

What is the reason that ProfiNET frames are discarded by default on Catalyst switches?

A. ProfiNET uses a nonstandard Ethernet frame format

B. The frames have an 802.1q tag with VLAN ID equal to 0 (zero)

C. Catalyst switches do not support ProfiNET traffic

D. A ProfiNET VLAN must be configured and enabled on a Catalyst switch

Answer: B

What is the reason that ProfiNET frames are discarded by default on Catalyst switches?

A. ProfiNET uses a nonstandard Ethernet frame format

B. The frames have an 802.1q tag with VLAN ID equal to 0 (zero)

C. Catalyst switches do not support ProfiNET traffic

D. A ProfiNET VLAN must be configured and enabled on a Catalyst switch

Answer: B

How are I/O timeout and Safety I/O timeout calculated?

A. An I/O connection will timeout based on the lower of 4x RPI or 100ms. Safety I/O timeout is calculated as 4xRPI.

B. An I/O connection will timeout based on the lower of 3x RPI or 100ms. Safety I/O timeout is calculated as 3xRPI.

C. An I/O connection will timeout based on the lower of 4x RPI or 150ms. Safety I/O timeout is calculated as 2xRPI.

D. An I/O connection will timeout based on the lower of 3x RPI or 150ms. Safety I/O timeout is calculated as 3xRPI.

Answer: A

A shutdown in the cookie cutter machine was traced to a broken network cable. What are two reasons that explain why using DLR is an appropriate choice for network resiliency? (Choose two)

A. DLR is designed for single network operation at the machine level

B. Moving to a linear topology will reduce the number of cables and so reduce risk of cable failure

C. DLR is the only resiliency technology that is supported by CIP Safety

D. Layer 2 resiliency protocols like REP and RSTP do not have a fast enough convergence time for motion control

E. Half of the network traffic goes clockwise on the ring and the other half counterclockwise, reducing by 50% the impact of cable failure

Answer: A,D

A shutdown in the cookie cutter machine was traced to a broken network cable. What are two reasons that explain why using DLR is an appropriate choice for network resiliency? (Choose two)

A. DLR is designed for single network operation at the machine level

B. Moving to a linear topology will reduce the number of cables and so reduce risk of cable failure

C. DLR is the only resiliency technology that is supported by CIP Safety

D. Layer 2 resiliency protocols like REP and RSTP do not have a fast enough convergence time for motion control

E. Half of the network traffic goes clockwise on the ring and the other half counter­clockwise, reducing by 50% the impact of cable failure

Answer: A,D

あなたが使用したりしてもCiscoの200-601試験問題集ダンプを考慮しないことを決定する前に、あなたはそれが何であるかを知る必要があり、どのようにまたはなぜティック。試験は基本的に非常に詳細な電子書籍はManaging Industrial Networking for Manufacturing with Cisco Technologies試験の値、または全体の認定、200-601の質問と回答の値が含まれています。200-601試験参考書は、情報が含まれている場合は、本明細書に信頼性があるということです。Ktestは、研究課題、と回答スマートである場合、これは順番にユーザーが必要です。これは、試験の準備を通常の、正当なより多くの時間よりも多くを必要とするかもしれません。

Ktestの Cisco CCNA Industrial資格 200-601試験参考書はIT上位な専門家がKtest 200-601試験参考書について自分の専門的な知識と経験を利用して研究したものでございます。勉強者のために試験問題は試験を完全に含んで問題集をお勧めします。Ktestが開発した問題集は実際的な問題と同じで、Ktestの200-601試験参考書を参考して、受験の自信を向上させることが出来ます。Ktestは勉強者に認定問題の提供に努力して、初心者としても認定に合格できます。問題と答えを暗記しただけで、素人としても合格できます。Ktestは200-601試験参考書の合格率を高めるのウエブサイトで、Ktest中のIT業界の専門家が研究を通じてKtest 200-601試験参考書について問題集を研究し続けています。KtestのManaging Industrial Networking for Manufacturing with Cisco Technologies試験問題集を選られば、絶対に成功することができます。